HELP! I hold a hugely old-fashioned Singer sewing apparatus that i sort of adjectives. I can't amount out how to draw from ...?
Answers: I have one of these and thank god I also hold the instruction book that came beside it or I never would have figure it out either! The bobbin is located within a sliding door on the base of the contrivance. Slide the door open and press the round button. They're calling it the bobbin ejector. This will lift the bobbin and it can easily be taken out. Threading the bobbin can be complicated. The instructions are two page long with diagrams. I will skip to replacing the bobbin once it is threaded. Once you hold a threaded bobbin put it back contained by the same place you originally took it out of (called the bobbin case). Draw the thread into the slot within the bobbin case. Pull the thread toward the right. Close the sliding door. Hope this help! By the way the instruction book say "Singer Electric Sewing Machine 66-8".
Put it in a place of honour as an antique.
i in truth have one that be my great grandmothers
the thread in the bottom is call the bobbin
first thread the top part
later when you have the thread wound around the bobbin itself, put the bobbin surrounded by with the thread coming sour to the right
hook the thread on the little silver hook by pulling towards you
then use the tiller on the side that makes the nozzle move and turn it toward you
then when the plunger is coming back up view for the bottom bobbin thread to come up and pull it up.
your domestic device is now threaded.
bobbin thread.
Don't know what model you own, but Singers of what I think this vintage would be (and this is a comparatively youthful machine, 50 years ripened or so) have removeable bobbin cases. You remove the slide plate, conquer in and unhook the bobbin crust, and then install the bobbin and reverse the process.
How to integer out what model you've got:
http://www.singerco.com/support/model_nu...
Once you've get the model number, you may be able to find the instruction encyclopaedia here:
http://parts.singerco.com/ipinstmanuals/...
If not, let us know what model.
Don't forget to verbs and oil (with sewing contraption oil, not 3-in-1 or WD-40) until that time using this. And inspect the wiring in moderation.
are u trying to thread the needle? look for the nozzle and if it's the machine i'm thinking of u can solely thread it in from one direction. if u thread it the wrong style the machine will not sew. unless ur discussion about puttting surrounded by a bobbin. then u enjoy to have the bobbin bursting with thread and uncap usually a silver piece that usually slides to the side and when open appropriate ur left foot and snap the bobbin in to the right side surrounded by that hole, turn it gently and it will snap into place. apt luck =)...
There should be a little slide door near a hole in it. The hypodermic goes into this hole. The slide should own a little thumbnail groove in it. Use the pit to slide the door open. The bobbin is inside. Be sure you document how it is oriented so you can replace it like peas in a pod way. You hold to take the bobbin spool out of the bobbin and twirl it with thread outside the contraption. There should be a small driven shaft on the top of the machine to do that beside.
Bert
The knee lever is certainly part of the footpedal which is mounted inside the cabinet. When you press near your knee the lever in reality pushes down on the controller where your foot usually would if it be on the floor.
As far as where the bobbin and bobbincase (holds the lower thread) is that depends on what caring of machine it is which you haven't stated. Its other just below the syringe no matter what, sometimes down a sliding door. Thats for a rotary hook that goes around. Really out-of-date machines can have whats call a shuttle bobbin and these go side to side. None the smaller quantity, it will still be just below the plunger. Is there a bullet shaped intent below the needle after you slide overt the cover? Thats a boat bobbin with a long spool inside. You'll involve to read up on bobbins and bobbincases for rotary machines and shuttle machines.
Good luck.
Rick
More Questions and Answers...