Wood floor next to dents from lofty heels.?
Is in that any finishing products that will make the wood a harder polish, so try and reduce the risk again?
Answers: x. you involve to belt sander it to just below the dents, consequently there is a diamond firm varnish you can get. suitable luck its a lot of not easy work just done my audience way near the same problem, cant bestow you the exact name of the varnish as i used it adjectives, but ask where you hire the belt sander. x
weakly sand any big holes fill next to wood filler and stain and lacquer a few coats of clear varnish will make it stronger
Actually, formerly you sand the floor, you might try something that worked for me.
I have an behind the times, old, cedar chest. I used to enjoy a huge dog, who when playing with the kids, somehow skidded across the top of the cedar chest, going away deep scratch.
I took a wet hip bath towel, rung out somewhat, and then took a steam iron and go back and forth across the low scratches. It took roughly speaking ten minutes and the scratches be gone. These were adjectives scratches.
It surely would hurt to try earlier you go to adjectives the trouble of sanding.
As far a a finish to use to impart the floor a harder glaze; I would shift for a bar top type finish, but distinctly check with a floor specialist first.
Good luck to you.
use three coats of polyurethane after sand. That will stand up to a lot of swearing. If you are taking on the job yourself, be sure to confer to someone who does it professionally who's work you have see, to get the best prep methods and what to do between coats of poly.
I enjoy all my rental property wood floors done this method and its reasonably priced and extremely durable. Many floor refinishers use two coats of poly, but this guy does three and you can see a big difference within the shine and the durability.
My floors have other been oak, maple or pine, so double check next to a pro to see if poly is right for cherry before you budge forward with it, but I muse it would be good.
I guess my interrogate back might be is it hardwood or laminate?
Cherry is a hardwood, and unless seriously of Mariachi dancing be taking place on the floor; Dents would enjoy to be pretty strongly "forced". Scratches are common; surrounded by that a floor endures more abuse than most other surfaces; but then here is the question of IF; or HOW it be clear coated.
DO NOT think WOOD fillers until you determine the scar.
Sanding a floor is a messy job; and best done by Pros. It equates to LARGE footprint sanders to alieviate the possibility of in plain sight DIPS over the surface.
We can't know how obvious, or even unsafe these dings might be to traffic over the floor; but scratch removal is the easier errand.
If the floor looks like it be hit by a HAIL storm, I'd go to the capitalist, for ONE, Then to the vendor, the contractors, and probably the company that manufactured the Clear coat as ably.
On a light hearted register you might practice the Japanese tradition of shoe removal.
Steven Wolf
There is a way to curtail the depth of the indentations. This sounds drastic but it works. Dip a rag contained by methylated spirits. Squeeze it into the indent. Set fire to the meths the vapour will burn above the floor smooth the combination of moisture and heat draws the wood up. Please don't set your house smouldering. If there are lots of indents it will be a laborious duty but saves sand gouges within your floor as it will only require a muted sanding to finish.
Been within, sorted that...... Sand the floor to remove the varnish as best you can, paint stripper in the dents.. Get an out-of-date iron, wet cloth, and steam the dents out. The steam cause the fibres of the wood to 'uncompress' and the dents come out most of the road. Long job, but spend a bit of time every evening, soon done. Then, hire a valid floor sander, and sand the whole lot as one. Realisticly, varnish , however easier said than done it is will not protect. BAN HIGH HEELS
Big sander, lots of dust, smelly stain and polyurethane, big mess, big bill. Good Luck
More Questions and Answers...