I enjoy a quiz near electric wiring a subterranean vault buoyant socket and a oil lamp switch and crossroads box.?
First of adjectives they had the black lead coming from the switch conncected to the one side screw on the light socket-- No problem in that.
Second they had the white telecommunication coming from the switch connected by a wire nut to the black wires contained by the junction box.
I did not similar to the looks of this. The other side screw of the light socket have a white jumper lead coming off the white wires pigtailed together.The switch works fine, it never cause a dead short it lately looks like they did it backwards. Other: concern is that it is mature wiring and they did not use cable nuts they just twisted the wires together and soldered some and tape over. I hate the 3 contained by. bare rope just solder/tape over
Answers: That's in actuality pretty common... I'm not crazy more or less mixing colored wires on the same circuit any, so I always get an extra spool of black, and white wires to run switches.
I imagine those wires on the switch are jacketed together? That's the most adjectives use of dual colored wire... you go and get the wires in the one 'romex' strand... and instead of blistering it back, and using twice as much lead (to get duplicate color) the previous technician just used the other lead in the strand, to complete the switch circuit. It is a secure practice, altho it can get confusing, hehehe. As I said, I prefer to get an extra roll or two... however, if youre just doing one house, its not worth the investment contained by additional line.
You can still go contained by and add flex nuts, where they will fit. Clip sour any wires that are too long, and install the wire nuts. I budge the extra step and tape the lead nuts, to prevent them from coming off if the wires are twisted any during handling. Use a suitable quality cassette.
If the wiring is 'cloth wrapped'-- it is indeed antediluvian, and you should rewire the home. Cloth wrapped wiring is ancient enough in a minute, that it is a fire hazard. If it is the typical 'rubber' jacket, afterwards I would inspect the 'rubber' to see if it is brittle or cracked...if it is.. I would rewire the house.
If for any reason, you settle on to rewire the home, seriously consider installing a new circuit box. Our home have 60 amp service when we moved in... I replaced it near a very generous 200 amp service box. The utility company told me to upgrade my meter base (and I did), and consequently they went ahead and upgraded the transformer supplying power to our home, and our neighbors, and run new wires to my flagstaff for me. They didnt charge for any of that. I was competent to eliminate adjectives of the old cloth wrapped wires within the home, and had some room for unsullied circuits (I detest sharing a circuit for my computers with anything else, lol).
Good Luck
the white line does NOT go to the switch.
solitary the black wire is interrupted by the switch.
useing a pullover wire to extend a telecommunication is ok as long as its properly covered and marked, if the wireing have a cloth type covering then its dated, and they didn,t have flex nuts then, it be soldered and taped.
It sounds similar to it was done correctly. The black from the source should be connected to the black on the wispy through the switch. What they apparently did NOT do was use black video to "mark" the white wire from the switch as a hot telecommunication (BOTH wires to the switch are hot wires).
Bert
You did everything correct, this is what is called a switch leg. Since it is standard to use 2 lead (w/ground) romex on all residential construction. It is inwardly code to use one section from the fork box to the switch box. How it is hooked up: you have a constant hot nurture on the white and your switch leg (which only have power when the switch is on) is the black, this is the preferred way to connect it. Then it is sent from the T-junction box to the light on the black cable (switch leg) and a white wire is connected to other nonpartisan wires. ( i normally dot the white that is the constant power to the switch beside black tape to indicate that it is supposed to be a hot leg).
Very adjectives to see that in everyday homes. The solder is in actual fact a better connection than the telecommunication nuts. Best not to monkey with stuff, especially if your house is outdated. Most often the armour, electrical systems don't go bleak until they are tampered near. If you feel you own to investigate still the most common problem beside old houses is unbecoming wattage in incandescent lights(*) Plus to supply to the fact the lights themselves aren't resourcefully insulated for heat to dissipate. The boil usually leads to wear and slit on thin ceiling and in worst cases in actual fact causes fire.
(*) Romex electric wiring only. Bx (Metal Sheath) electrics w/ out a ground is another problem in and of itself.
That sounds right to me. the solder and cartridge is old academy. You could cut, re twist and rope nut, but it should be fine the way it is. but your white line being converted to a hot should hold a piece of black tape or paint on it depicting that it is a hot head.
hope this helps. not easy to visualize without certainly seeing it.
More Questions and Answers...