Painting drywall comfort!?
1. the cement is all over the wall... can I paint over this or should I sand it? whats the best instrument?
2. Do I need some sort of primer on the drywall until that time I paint?
3. How do I put a splatter-type texture on the wall? do I mix something into the paint? do I put it on before I paint?
gratitude everyone
Answers: Hi...OK so answer to #1 no you cannot paint over the glue.....be in motion get some stuff softener or wallpaper remover, spray it on the glue spots and srape it rotten with a scraper from the paint dept at Lowe's.... later you need to draw from some TSP and clean your walls (also found surrounded by the paint dept) then the answer to #2 is yes, you entail to prime...then #3 here is a particular roller and paint you can buy for that "textured" look...also found surrounded by the paint dept....go to your local Lowe's and walk to the paint desk and someone there will put your foot you through your project....it sounds like alot, but it really isn't...honest luck
Definitely sand the walls before attempting to paint. Sanding is easier said than done work, so I suggest renting a hand sander from your local rental place. Your hand and shoulders will thank you. Then clean the dust from the walls previously you do anything else. Do use a primer; you'll get better paint coverage. Not sure more or less the splatter texture, but the clerks at the paint store are very educated.
I. I would suggest that you get as much of the epoxy resin off as you can. I didn't when I took the wallpaper stale of our bathroom wall and it's been a distress ever since. To remove look for a solvent at your local hardware store, follow directions.
2. I suggest using a primer before drawing. It helps get it more even. Paint covers better and sticks better too.
3. It depends on how large an nouns. For small areas you can get texture contained by spray cans> They work well for smaller areas. You can a small "hopper" sprayer, those work ably too.
For sure if you are texturing the wall you will want a primer. Make sure the wall is dry before putting on the primer. And when you put primer on, don't soak the texture too much, it will beome raining and it will be ruined.
I have used the texture surrounded by a spray can for vertical walls. It works pretty good for that. Not so hot for ceiling.
I have never have any luck with textured paints.
You can also return with texturing tools like those at "all-wall.com"
remove adjectives or the old paper/glue stuff. use drywall run through and drywall mud to float out bad spots. consent to dry and sand out smooth.
now, for an nouns this size you will need to use a spray rig, ( a compressor and a hopper), to spray texture, (texture is a sticky syrupy mix of dry wall compound and water. mix it surrounded by a 5 gallon bucket. you can adjust the thickness as needed but start beside very little sea and experiment until it is a thick syrup).
when its right adjust compressor to just about 110-120 psi, fill hopper no more than partially way, (it will be large is you fill it adjectives the way). experiment with nozzle until you acquire a heavy splatter or "red peel" spray. let it set up just about 20 to 30 minutes, then filch you mud knife and meekly knock down the texture giving it the spaltter drag look you want. to be precise if you want splatter drag. if not, spray a finer red peel and consent to it dry....it's hard to explain but that basicly it. shoot me email if you necessitate more info. GL with it.
Remove the cement get a flawless flexable scaper and hot water, .or step to paint store for remover. Always prime walls before you do anything, Kilz or C.I.L problem solver, you can bring roller covers that will give you your textured walls within many paterns, the paint store will provide you the texture material you will involve Spray cans Cost to much foe such a big errand as walls, get the stuff you mix yourself, righteous luck rember to use a drop sheet.
More Questions and Answers...