When the status light on a Harman Invincible pellet stove insert blinks three times, what does it mean?
Answers:
It appears that the question period has expired. If you have received an answer that meets your needs, please choose one of those as a 'best answer.' If you haven't received a good answer for your question, you may want to consider the following,
1) Re-post your question. Newer questions get more activity on Yahoo! Answers than old ones.
2) If you do re-post your question, consider why it wasn't answered the first time. Could it be more specific? Could it be worded better? Were there grammatical or spelling errors? Was it in the best category?
If it doesn't seem likely that re-posting your question will help you, then here's a listing of my favorite 'answer sites'. Maybe one of them will help you.
Answers.com http://www.answers.com/
Bartleby http://www.bartleby.com/
Yahoo Reference http://education.yahoo.com/reference/
HowStuffWorks http://www.howstuffworks.com/
Wikipedia http://en.wikipedia.org/wiki/Main_Page
Since I really haven't answered your question, it is not necessary to give me any points. Regards.
Other answers:
The information below came from the owner's manual for a PF100 Pellet Pro Furnace, could not find your exact model's owner's manual. Manufacturers generally use the same setup for most of their product. Can't be for sure though. Hope this helps, I put the link to the site below. Good Luck.
Status light error messages:
1 Blink: Indicates control board self diagnostic failure. This
requires a manual reset*.
3 Blinks: Indicates ESP (Exhaust Sensing Probe) failure. This
requires a manual reset*.
4 Blinks: Can occur only in the Automatic Mode and
indicates the Wall Control has failed or is not installed. If a
Wall control is then installed the status light will automatically
reset.(Note) only after the unit has warmed up.
5 Blinks: (In Auto Light Mode Only)
Indicates that the igniter has failed to light the fire after 4
consecutive 8 minute attempts. To reset - Turn the Mode
Selector to OFF and then back to Automatic.
6 Blinks : Indicates that the control has calculated poor or
incomplete combustion occurring for more than 50 minutes.
A six blink status may be set if the stove is allowed to run out
of pellets. To reset, turn mode selector to "OFF" then back
on to the desired mode. If the unit was not out of pellets, see
Troubleshooting section, Page 35, for more details.
* Manual reset, disconnect power at the circut breaker for
a few seconds and reconnect. If error still occurs call your dealer.
The information below came from the owner's manual for a PF100 Pellet Pro Furnace, could not find your exact model's owner's manual. Manufacturers generally use the same setup for most of their product. Can't be for sure though. Hope this helps, I put the link to the site below. Good Luck.
Status light error messages:
1 Blink: Indicates control board self diagnostic failure. This
requires a manual reset*.
3 Blinks: Indicates ESP (Exhaust Sensing Probe) failure. This
requires a manual reset*.
4 Blinks: Can occur only in the Automatic Mode and
indicates the Wall Control has failed or is not installed. If a
Wall control is then installed the status light will automatically
reset.(Note) only after the unit has warmed up.
5 Blinks: (In Auto Light Mode Only)
Indicates that the igniter has failed to light the fire after 4
consecutive 8 minute attempts. To reset - Turn the Mode
Selector to OFF and then back to Automatic.
6 Blinks : Indicates that the control has calculated poor or
incomplete combustion occurring for more than 50 minutes.
A six blink status may be set if the stove is allowed to run out
of pellets. To reset, turn mode selector to "OFF" then back
on to the desired mode. If the unit was not out of pellets, see
Troubleshooting section, Page 35, for more details.
* Manual reset, disconnect power at the circut breaker for
a few seconds and reconnect. If error still occurs call your dealer.